Aviation Regulations Logo
§ 25.729
Retracting mechanism.
(a) General. For airplanes with retractable landing gear, the following apply:
(1) The landing gear retracting mechanism, wheel well doors, and supporting structure, must be designed for—
(i) The loads occurring in the flight conditions when the gear is in the retracted position,
(ii) The combination of friction loads, inertia loads, brake torque loads, air loads, and gyroscopic loads resulting from the wheels rotating at a peripheral speed equal to 1.23VSR (with the wing-flaps in take-off position at design take-off weight), occurring during retraction and extension at any airspeed up to 1.5 VSR1 (with the wing-flaps in the approach position at design landing weight), and
(iii) Any load factor up to those specified in § 25.345(a) for the wing-flaps extended condition.
(2) Unless there are other means to decelerate the airplane in flight at this speed, the landing gear, the retracting mechanism, and the airplane structure (including wheel well doors) must be designed to withstand the flight loads occurring with the landing gear in the extended position at any speed up to 0.67 VC.
(3) Landing gear doors, their operating mechanism, and their supporting structures must be designed for the yawing maneuvers prescribed for the airplane in addition to the conditions of airspeed and load factor prescribed in paragraphs (a)(1) and (2) of this section.
(b) Landing gear lock. There must be positive means to keep the landing gear extended in flight and on the ground. There must be positive means to keep the landing gear and doors in the correct retracted position in flight, unless it can be shown that lowering of the landing gear or doors, or flight with the landing gear or doors extended, at any speed, is not hazardous.
(c) Emergency operation. There must be an emergency means for extending the landing gear in the event of—
(1) Any reasonably probable failure in the normal retraction system; or
(2) The failure of any single source of hydraulic, electric, or equivalent energy supply.
(d) Operation test. The proper functioning of the retracting mechanism must be shown by operation tests.
(e) Position indicator and warning device. If a retractable landing gear is used, there must be a landing gear position indicator easily visible to the pilot or to the appropriate crew members (as well as necessary devices to actuate the indicator) to indicate without ambiguity that the retractable units and their associated doors are secured in the extended (or retracted) position. The means must be designed as follows:
(1) If switches are used, they must be located and coupled to the landing gear mechanical systems in a manner that prevents an erroneous indication of “down and locked” if the landing gear is not in a fully extended position, or of “up and locked” if the landing gear is not in the fully retracted position. The switches may be located where they are operated by the actual landing gear locking latch or device.
(2) The flightcrew must be given an aural warning that functions continuously, or is periodically repeated, if a landing is attempted when the landing gear is not locked down.
(3) The warning must be given in sufficient time to allow the landing gear to be locked down or a go-around to be made.
(4) There must not be a manual shut-off means readily available to the flightcrew for the warning required by paragraph (e)(2) of this section such that it could be operated instinctively, inadvertently, or by habitual reflexive action.
(5) The system used to generate the aural warning must be designed to minimize false or inappropriate alerts.
(6) Failures of systems used to inhibit the landing gear aural warning, that would prevent the warning system from operating, must be improbable.
(7) A flightcrew alert must be provided whenever the landing gear position is not consistent with the landing gear selector lever position.
(f) Protection of equipment on landing gear and in wheel wells. Equipment that is essential to the safe operation of the airplane and that is located on the landing gear and in wheel wells must be protected from the damaging effects of—
(1) A bursting tire;
(2) A loose tire tread, unless it is shown that a loose tire tread cannot cause damage.
(3) Possible wheel brake temperatures.
[Doc. No. 5066, 29 FR 18291, Dec. 24, 1964, as amended by Amdt. 25-23, 35 FR 5676, Apr. 8, 1970; Amdt. 25-42, 43 FR 2323, Jan. 16, 1978; Amdt. 25-72, 55 FR 29777, July 20, 1990; Amdt. 25-75, 56 FR 63762, Dec. 5, 1991; Amdt. 25-136, 77 FR 1617, Jan. 11, 2012]