Aviation Regulations Logo
§ 125.509
Flammability reduction means.
(a) Applicability. Except as provided in paragraph (m) of this section, this section applies to transport category, turbine-powered airplanes with a type certificate issued after January 1, 1958, that, as a result of original type certification or later increase in capacity have:
(1) A maximum type-certificated passenger capacity of 30 or more, or
(2) A maximum payload capacity of 7,500 pounds or more.
(b) New Production Airplanes. Except in accordance with § 125.201, no person may operate an airplane identified in Table 1 of this section (including all-cargo airplanes) for which the State of Manufacture issued the original certificate of airworthiness or export airworthiness approval after December 27, 2010 unless an Ignition Mitigation Means (IMM) or Flammability Reduction Means (FRM) meeting the requirements of § 26.33 of this chapter is operational.
Table 1
Model—Boeing
Model—Airbus
747 Series
A318, A319, A320, A321 Series
737 Series
A330, A340 Series
777 Series
767 Series
(c) Auxiliary Fuel Tanks. After the applicable date stated in paragraph (e) of this section, no person may operate any airplane subject to § 26.33 of this chapter that has an Auxiliary Fuel Tank installed pursuant to a field approval, unless the following requirements are met:
(1) The person complies with 14 CFR 26.35 by the applicable date stated in that section.
(2) The person installs Flammability Impact Mitigation Means (FIMM), if applicable, that is approved by the FAA Oversight Office.
(3) Except in accordance with § 125.201, the FIMM, if applicable, are operational.
(d) Retrofit. Except as provided in paragraph (j) of this section, after the dates specified in paragraph (e) of this section, no person may operate an airplane to which this section applies unless the requirements of paragraphs (d)(1) and (d)(2) of this section are met.
(1) Ignition Mitigation Means (IMM), Flammability Reduction Means (FRM), or FIMM, if required by §§ 26.33, 26.35, or 26.37 of this chapter, that are approved by the FAA Oversight Office, are installed within the compliance times specified in paragraph (e) of this section.
(2) Except in accordance with § 125.201 of this part, the IMM, FRM or FIMM, as applicable, are operational.
(e) Compliance Times. The installations required by paragraph (d) of this section must be accomplished no later than the applicable dates specified in paragraph (e)(1), (e)(2) or (e)(3) of this section.
(1) Fifty percent of each person's fleet of airplanes subject to paragraph (d)(1) of this section must be modified no later than December 26, 2014.
(2) One hundred percent of each person's fleet of airplanes subject to paragraph (d)(1) of this section must be modified no later than December 26, 2017.
(3) For those persons that have only one airplane of a model identified in Table 1 of this section, the airplane must be modified no later than December 26, 2017.
(f) Compliance after Installation. Except in accordance with § 125.201, no person may—
(1) Operate an airplane on which IMM or FRM has been installed before the dates specified in paragraph (e) of this section unless the IMM or FRM is operational, or
(2) Deactivate or remove an IMM or FRM once installed unless it is replaced by a means that complies with paragraph (d) of this section.
(g) Inspection Program Revisions. No person may operate an airplane for which airworthiness limitations have been approved by the FAA Oversight Office in accordance with §§ 26.33, 26.35, or 26.37 of this chapter after the airplane is modified in accordance with paragraph (d) of this section unless the inspection program for that airplane is revised to include those applicable airworthiness limitations.
(h) After the inspection program is revised as required by paragraph (g) of this section, before returning an airplane to service after any alteration for which airworthiness limitations are required by §§ 25.981, 26.33, 26.35, or 26.37 of this chapter, the person must revise the inspection program for the airplane to include those airworthiness limitations.
(i) The inspection program changes identified in paragraphs (g) and (h) of this section must be submitted to the operator's assigned Flight Standards Office responsible for review and approval prior to incorporation.
(j) The requirements of paragraph (d) of this section do not apply to airplanes operated in all-cargo service, but those airplanes are subject to paragraph (f) of this section.
(k) After the date by which any person is required by this section to modify 100 percent of the affected fleet, no person may operate in passenger service any airplane model specified in Table 2 of this section unless the airplane has been modified to comply with § 26.33(c) of this chapter.
Table 2
Model—Boeing
Model—Airbus
747 Series
A318, A319, A320, A321 Series.
737 Series
A300, A310 Series.
777 Series
A330, A340 Series.
767 Series
757 Series
(l) No person may operate any airplane on which an auxiliary fuel tank is installed after December 26, 2017 unless the FAA has certified the tank as compliant with § 25.981 of this chapter, in effect on December 26, 2008.
(m) Exclusions. The requirements of this section do not apply to the following airplane models:
(1) Convair CV-240, 340, 440, including turbine powered conversions.
(2) Lockheed L-188 Electra.
(3) Vickers VC-10.
(4) Douglas DC-3, including turbine powered conversions.
(5) Bombardier CL-44.
(6) Mitsubishi YS-11.
(7) BAC 1-11.
(8) Concorde.
(9) deHavilland D.H. 106 Comet 4C.
(10) VFW—Vereinigte Flugtechnische VFW-614.
(11) Illyushin Aviation IL 96T.
(12) Bristol Aircraft Britannia 305.
(13) Handley Page Herald Type 300.
(14) Avions Marcel Dassault—Breguet Aviation Mercure 100C.
(15) Airbus Caravelle.
(16) Fokker F-27/Fairchild Hiller FH-227.
(17) Lockheed L-300.
[Doc. No. FAA-2005-22997, 73 FR 42502, July 21, 2008, as amended by Amdt. 125-57, 74 FR 31619, July 2, 2009]